Product
group
FF
YWRIT - Din rail 1-20mA adjustable single setpoint trip amp.
11WRIT - 11 pin plug in 1-20mA adjustable single setpoint trip amp.
YWRI2T - Din rail 1-20mA two adjustable setpoints trip amp, 2 x SPCO outputs “Low” & “High”.
YWRIT, 11WRIT
“Auto Reset” without latching mode. This mode is determined by terminals Y1 & Y2 or pins 9 & 11 left open. The output relay is energised when the monitored circuit rises above the level selected via the front potentiometer. The output relay will de-energise when the current falls back below the level selected less the set hysteresis adjustable 5 to 50%, set via a second potentiometer. If the auxiliary supply is lost at any time the relay will also de-energise.
“Manual Reset” latching mode. This mode is determined by a wired link between terminals Y1 & Y2 or pins 9 & 11. The output energises when the monitored circuit rises above the level selected by the front potentiometer. Once energised the relay will remain latched even if the monitored current falls below the set level less any selected hysteresis. Resetting is achieved by opening the link between terminals Y1 & Y2 or pins 9 & 11 or by removing the auxiliary supply. If whilst resetting the monitored current is still above the set level a reset will not be achieved. It is normally preferable in the latching mode to have the adjustable hysteresis set at minimum.
YWRI2T
Two setpoint trip amp. Providing two separately controllable trip levels. With R1 selected as the “High” level and R2 as the “Low” level. When the monitored signal current rises above R2 set level R2 relay will energise. If the current continues to rise above R1 set level, relay R1 will energise. Conversely as the monitored current falls R1 will de-energise, if the fall continues R2 will de-energise. The unit has a built in fixed hysteresis of 2% at each setpoint to avoid relay “chatter”. The YWRI2T does not have a latched option and is therefore “auto” reset on both relays.
Adjustable Time Delays
The trip amps YWRIT & 11WRIT have 3 separately adjustable 0.1-10 sec delays. A start up delay activated by the connection of the auxiliary supply, therefore if a control circuit is going to be permanently live the time delay will only ever be active once. A delay on rising current and a delay on falling. The YWRI2T does not have any time delays.
DC Auxiliary Supply Versions
DC auxiliary supply versions are as standard non isolated. For these versions the supply and the measured current must be isolated from each other and must not exceed 50V DC. On request at extra cost isolated versions can be manufactured utilising internally a DC to DC converter.
Supply & Measuring
Nominal supply tolerance: ±15%
Isolation AC versions: Via transformer
Isolation DC versions:
No as standard
Yes via optional internal DC to DC converter
Power consumption: 3VA max
Hysteresis:
Adjustable 5 to 50% of Ie
YWRI2T fixed at 2%
Repeat accuracy:
±2% at constant ambient
±5% across temperature range
Response time:
100 mSec on make
200mSec on break
Input range: 1-20mA adjustable
Max over current: 1Amp (max 1 sec)
Input impedance: 10 Ohms
Time delays:
0.1-10 secs separately adjustable
YWRI2T no delays
Relay output
Output contacts:
SPCO 10Amps/250V AC1
DPCO 8Amps/250V AC1
Mechanical life: 30 Million ops
Electrical life: 200K ops at max rated load
General
Operating temperature: -20°C to +65°C
Storage temperature: -20°C to +65°C
Max cable size: 4mm
CE marked: Yes
In accordance with:
EN61000-6-1: 2007
EN61000-6-3: 2007
EN61010-1: 2002
Housing material: Polycarbonate, Auto extinguishable to UL 94 V-0
TYPE
YWRIT (din rail SPCO)
11WRIT (11 pin SPCO)
YWRI2T (din rail 2 x SPCO)
COIL VOLTAGE
440VAC
415VAC
400VAC
380VAC
230VAC
110VAC
48VAC
24VAC
*48VDC
*24VDC
* No isolation on DC versions as standard, on request at extra cost isolated versions are available.
Receive updates about our offers, latests products and more, directly to your inbox